Sames | S3 P HTI Manual Airspray Spray Gun Pressure

Description

Very high transfer efficiency
Outstanding atomization quality
Improved ergonomics: smallest and lightest gun

Performance

♦Very fine atomization for a high-gloss finish
♦Perfectly balanced fan for easy application

Productivity

♦Ergonomic due to a very comfortable body design
♦EZ-Adjust aircap for easy rotation adjustment
♦Reduced trigger effort due to its in-line air valve
♦One of the lightest manual spray guns in its category & perfectly balanced: reducing repetitive strain injuries (RSI)
♦Large range of projectors (aircap + nozzle + needle) & stainless steel fluid passages (compatible with a large range of solvent and water-based materials) allowing it to be used for all kinds of applications

Sustainability

♦Designed from high-end materials (stainless steel, anodized forged aluminum body, brass) in conjunction with Sames's machined projectors (aircaps + nozzle + needle) ensure extended product life
♦Reduction in the number of components makes for easy and quick maintenance

S3 P HTI is our most compact and lightest gun, it is HVLP compliant to show an outstanding finish quality, with very little product loss.

Technical data table

Designation	Value	Unit: metric (US)
Maximum Fluid Pressure	6 (87)	bar (psi)
Maximum Fluid Outlet	131 (4.6)	cc/min (oz/min)
Minimum Fluid Outlet	80 (2.8)	cc/min (oz/min)
Maximum Air Pressure	6 (87)	bar (psi)
Recommended Air Pressure (min)	2 (29)	bar (psi)
Air Consumption	12 (7.1)	m3/h (cfm)
Maximum Fluid Temperature	50 (122)	°C (°F)
Air Inlet	M 1/4" NPS
Fluid Inlet	M 1/4" NPS
Polished Forged Aluminum Body	♦
Wetted Parts, Stainless Steel	♦
Ph	5 - 8
Weight	388 (13.7)	g (oz)

Equipment

Designation	Max Fluid viscosity (CA 4)	Projector	Nozzle size	Air Consumption	Fluid Output	Fan width at 20cm (8in)	Part number
S3 PRESS	-	-	-	-	-	-	135150200
S3 PRESS	14 - 20 s	08 EPX K HVLP	0.8 mm (0.031 in)	12 m3/h (7.1 cfm)	300 cc/mn (10.1 oz/mn)	25 cm (9.8 in)	135150204
S3 PRESS	20 - 30 s	10 EPX K HVLP	1.0 mm (0.039 in)	12 m3/h (7.1 cfm)	461 cc/mn (15.6 oz/mn)	26 cm (10.2 in)	135150205
S3 PRESS	30 - 40 s	12 EPX K HVLP	1.2 mm (0.047 in)	12 m3/h (7.1 cfm)	745 cc/mn (25.2 oz/mn)	26 cm (10.2 in)	135150206

Accessories

Designation	Max Fluid viscosity (CA 4)	Aircap	Nozzle size	Needle	Compatibility	Air Consumption	Fluid Output	Fan width at 20cm (8in)		Part number
PROJECTOR	14 - 20 s	EPX K HVLP	0.8 mm (0.031 in)	0.8	-	12 m3/h (7.1 cfm)	80 cc/mn (2.7 oz/mn)	25 cm (9.8 in)	1	031150004
PROJECTOR	20 - 30 s	EPX K HVLP	1.0 mm (0.039 in)	1.0	-	12 m3/h (7.1 cfm)	92 cc/mn (3.1 oz/mn)	26 cm (10.2 in)	2	031150005
PROJECTOR	30 - 40 s	EPX K HVLP	1.2 mm (0.047 in)	1.2	-	12 m3/h (7.1 cfm)	131 cc/mn (4.4 oz/mn)	26 cm (10.2 in)	3	031150006
AIRCAP	-	EPX K HVLP	-	-	-	-	-	-	4	132150100
NEEDLE	-	-	-	0.8	nozzle 0.8	-	-	-	5	033150100
NEEDLE	-	-	-	1.0	nozzle 1.0	-	-	-	6	033150500
NEEDLE	-	-	-	1.2	nozzle 1.2	-	-	-	7	033150200
NOZZLE	14 - 20 s	-	0.8 mm (0.031 in)	-	aircap EPX K HVLP	-	-	-	8	134630400
NOZZLE	20 - 30 s	-	1.0 mm (0.039 in)	-	aircap EPX K HVLP	-	-	-	9	134630100
NOZZLE	30 - 40 s	-	1.2 mm (0.047 in)	-	aircap EPX K HVLP	-	-	-	90	134630200

Spare Parts

Designation	Details		Part number
PACKAGE OF SEALS S3 GUN	Pack of seals	2	129150901
SERVICING KIT S3 GUN	Maintenance pack (includes a pack of seals + gun components)	3	129150902

Technologies

HVLP

This compliant technology ensures high transfer efficiency (minimum 65%) with reduced atomizing air pressure of 0.7 bar maxi.

Documents

Select all documents

S3 P HTI Manual Airspray Spray Gun Pressure

Format : application/pdf
Size : 429Ko

Select the document

Catalog Airspray Range Sames (English version)

Catalog airspray range sames kremlin

Format : application/pdf
Size : 14Mo

Select the document

General Catalog (only for North American market) Sames

General Catalog North America

Format : application/pdf
Size : 3Mo

Select the document

Instruction Manuals

Select all documents

Materials

Primer Epoxy

Epoxy primer/sealer is a non-porous finish that is typically recommended as the first base coat over bare steel.

Primer Epoxy Multi-Component

Epoxy primer/sealer multi-component is a non-porous finish base mixed with a hardener that is typically recommended as the first base coat over bare steel.

Primer Polyurethane Multi-Component

Designed to hide profile & surface imperfections, multi-component polyurethane primers & sealers improve adhesion of top coats to the substrate due to the addition of a hardener.

Primer Water-Based

Designed to hide profile & surface imperfections, water-based primers & sealers are environmentally friendly.

Primer Polyurethane

Designed to hide profile & surface imperfections, polyurethane primers & sealers promote adhesion of top coats to the substrate.

Enamel Water-Based

Enamel paint air dries to a hard, typically glossy finish, and is used for coating surfaces that are outdoors or otherwise subject to hard wear or temperature changes.

Water-Based Stains

Water-Based Wood Stains have all the advantages of oil-based stains. They spread easily, can be repaired, blend effortlessly & have plenty of open time. The thicker formula allows for controlled penetration, which will reduce blotching on softer woods such as Aspen, Pine & Maple.

Solvent-Based Stains

A wood stain consists of a colorant suspended or dissolved in an agent or solvent. Colored, or ''stained", finishes do not penetrate the pores of the wood to any significant degree.

CARC Water-Based

Chemical Agent Resistant Coating (CARC) is available in a water-based solution for environmental protection.

CARC Epoxy Multi-Component

Chemical Agent Resistant Coating (CARC) is a paint commonly applied to military vehicles to provide protection against chemical & biological weapons. The surface of the paint is engineered to be easily decontaminated after exposure to chemical warfare & biological warfare agents. The paint is also resistant to damage & removal by decontaminating solutions.

CARC Polyurethane Multi-Component

Chemical Agent Resistant Coating (CARC) can be two-component polyurethane paint commonly applied to military vehicles to provide protection against chemical & biological weapons.

Moisture-Sensitive Polyurethane Multi-Component

Catalyzed polyurethane clear coats and paints are prized for their durability and versatility around the world. They are used on everything from wood cabinetry, mill work and furniture to planes, trains, and automobiles. They are usually mixed with isocyanates in the hardener. The isocyanate component of polyurethane reacts with moisture in the air and form a hard crystalline structure.

Top Coat Polyurethane Multi-Component

Polyurethane Top Coat is a two- or three-pack isocyanate-cured polyurethane that gives a durable, high gloss finish. Isocyanates included in the hardener are moisture-sensitive & need a specific process for insulating the circuit.

Top Coat Epoxy

Top Coat Epoxys are used for decorative flooring applications, such as Terrazzo flooring, chip flooring & colored aggregate flooring.

Top Coat Epoxy Multi-Component

Two-part epoxy coatings were developed for heavy duty service on metal substrates & use less energy than heat-cured.

Top Coat Water-Based

Water-based polyurethane is popular because of its low odor & low toxicity. It goes on clear without adding a faint color like oil-based versions do & it dries much faster.

Top Coat Polyurethane

Polyurethane Top Coat gives a durable, high gloss finish.

Acid Catalyst Polyurethane Multi-Component

Multi-Component Epoxy Acid Catalyzing (AC) systems require a hardener or catalyst to dry/cure, which works by starting & maintaining the binder's curing process until the chemical reaction is complete. The solvent evaporates prior to & during the chemical reaction concluding a final film of lacquer, paint or filler. The catalyst is moisture-sensitive and requires a Flowmax® technology protection.

Acid Catalyst Epoxy Multi-Component

Multi-Component Epoxy Acid Catalyzing (AC) systems require a hardener or catalyst to dry/cure, which works by starting & maintaining the binder's curing process until the chemical reaction is complete. The solvent evaporates prior to & during the chemical reaction concluding a final film of lacquer, paint or filler. Curing times of AC products can be dramatically accelerated with heat application.

Metallic Epoxy

The newest metallic epoxy system on the market allows contractors to heighten the effects & make floors look three-dimensional.

Metallic Water-Based

Polyurethane water-based coatings offer a very high chemical/physical resistance & steel effect & are environmentally friendly.

Metallic Epoxy Multi-Component

A two-component 100%-solid epoxy blended with metallic pigments, Metal Fusion is self-leveling, allowing easy application & seamless floor surfaces.

Metallic Polyurethane

Polyurethane coatings are particularly recommended for application to surfaces subject to high levels of wear & tear where excellent chemical/physical resistance is required. The metallic parts will give a steel effect.