Sames | 40C50 Airmix Paint pump

Description

Suction rod or gravity hoppers
Two gun management available
Good chemical compatibility with GT, Chevron, PE seals

Performance:

♦ Economical with low air consumption
♦ Quiet air motor to preserve work environment
♦ air motor sizes available to deliver the product at the right pressure for high quality finish

Productivity:

♦ Construction without dead zones for quick flushing & product changeovers
♦ Mobile seal located on the piston ensures mechanical cleaning of the fluid section internal wall during pump run
♦ Lower mobile single lip packing (GT) for improved efficiency & reduced friction

Sustainability:

♦ Simple design with fewer parts for extended lifetime
♦ Polyfluid & PTFE graphite seal for improved wear resistance
♦ Triple chrome layer piston for exceptional durability

A large choice of accessories allows you to create various configurations to meet all customer requirements.

Technical data table

Designation	Value	Unit: metric (US)
Pressure Ratio	40:1
Maximum Fluid Pressure	240 (3480)	bar (psi)
Maximum Air Pressure	6 (87)	bar (psi)
Air Consumption	21.6 (12.7)	m³/h (cfm)
Maximum Temperature	60 (140)	°C (°F)
Cylinder	50 (1.7)	cc (oz)
Sound Level	77	dBa
Fluid Output at 30 cycles/mn	1.5 (0.4)	l/min (gal/mn)
Air Inlet	F 3/4" BSP
Fluid Outlet	M 1/2" JIC
Fluid Inlet	M 26 x x125
Weight	22 (48.5)	kg (lbs)

Equipment

Designation	Version	Fluid inlet	Suction rod	Drain rod	Atom.air regulator	Fluid press.Air regulator	Seal	Filter	Part number
40C50 Airmix Bare pump	bare	F 1/2 BSPP	-	-	-	-	Chevron+GT	-	151775000
40C50 PUMP W/M W/O FILTER W/O SUCTION ROD	Wall Mount	M 26x125	-	-	-	o	Chevron+GT	-	151775050
40C50 PUMP W/M W/O FILTER WITH SUCTION ROD DIA 23	Wall Mount	M 26x125	Dia.23	-	-	o	Chevron+GT	-	151775100
40C50 PUMP W/M WITH FILTER W/O SUCTION ROD	Wall Mount	M 26x125	-	-	-	o	Chevron+GT	o	151775150
40C50 PUMP W/M WITH FILTER AND SUCTION ROD DIAM 23	Wall Mount	M 26x125	Dia.23		-	o	Chevron+GT	o	151775200

Accessories

Designation					Part number
Two Post Cart w/o plate					051221000
Pump Mounting Plate with straps					056100199
Stainless steel Suction rod Ø23 plunging tube length elbowed 570 mm M26x125					149596150
Stainless steel Suction rod Ø23 plunging tube length 1000mm elbowed (for 200 liters drums) M26x125					149596160
Stainless steel drain rod Ø16 elbowed F18 x 125					049596000
Fluid filter 3/8 Mesh 12					155580400

Spare Parts

Designation					Part number
Seal kit for 1000-4 air motor including reversing-block seals					146270991
Full maintenance kit for 1000-4 air motor including reversing-block seals					146270995
Seal kit for C50 hydraulic section (Chevron/GT)					144950091
Full maintenance kit C50 hydraulic section (Chevron/GT)					144950096
Seal kit for C50 hydraulic section (Chevron/Chevron)					144950090
Full maintenance kit C50 hydraulic section (Chevron/Chevron)					144950095
Upper packing with GT seal					144950100
Chevron seal, PE					909051103
Ball Ø 16, 316L stainless steel					907414142
Ball Ø 9.52, 316L stainless steel					907414623

Technologies

Chevron Sealing

A Chevron packing set independently reacts to pressure & automatically affects a seal.

GT Sealing

This technology represents a new generation of sealing designed to extend the life of a pump piston.

Cup Lub

A pump has a cup filled with lubricant at the top of the liquid section.

2 Ball

2 ball pumping technology is highly utilized in fluid sections with one ball / seat for suction & the other ball / seat for feeding.

Triple Chrome Layer

This is a special treatment for very high sustainability & is applied to the piston of the fluid section of a pump.

Documents

Select all documents

40C50 Airmix

Format :
Size : 0Po

Select the document

Leaflet 10C50 -20C50 -40C50 Paint Pump (English version) Sames

Format : application/pdf
Size : 499Ko

Select the document

Catalog Airless Range Sames (English version)

Format : application/pdf
Size : 10Mo

Select the document

General Catalog (only for North American market) Sames

General Catalog North America

Format : application/pdf
Size : 3Mo

Select the document

Materials

Primer Epoxy

Epoxy primer/sealer is a non-porous finish that is typically recommended as the first base coat over bare steel.

Primer Epoxy Multi-Component

Epoxy primer/sealer multi-component is a non-porous finish base mixed with a hardener that is typically recommended as the first base coat over bare steel.

Primer Polyurethane Multi-Component

Designed to hide profile & surface imperfections, multi-component polyurethane primers & sealers improve adhesion of top coats to the substrate due to the addition of a hardener.

Primer Water-Based

Designed to hide profile & surface imperfections, water-based primers & sealers are environmentally friendly.

Primer Polyurethane

Designed to hide profile & surface imperfections, polyurethane primers & sealers promote adhesion of top coats to the substrate.

Anti-Corrosion Water-Based

Some anti-corrosion materials are available in water-based versions. These green paints have a longer dry time, but meet most environmental requirements & have excellent protective qualities.

Anti-Corrosion Epoxy Multi-Component

The Anti-Corrosion Epoxy Multi-Component product is highly resistant to marine & industrial environments, buried conditions, ground water, effluents, salt water & a wide range of oils & chemicals.

Anti-Corrosion Epoxy Free Solvent

Solvent-free epoxy coatings are designed for long-term protection of steel & concrete structures against corrosion, abrasion & chemical attack. Operating temperature ranges from –40F to 1040F.

Anti-Corrosion Polyurethane Multi-Component

A two-component efficient coating product, used as first layer on metallic surfaces & in a wide range of painting systems. Forms an excellent quality anti-corrosive polyurethane film, ensuring the adherence between the surface & the next layer of the painting process.

Anti-Corrosion Epoxy

Anti-Corrosion Epoxy is applied for active anti-corrosive & anti-rust protection of iron & steel surfaces that are to be coated. It is extremely hard & resistant to friction. It is particularly resistant to diluted acids, alkalis, petroleum products, some solvents, water, sea water, and more.

Anti-Corrosion Epoxy High Solid

Used for the steel structures of steel pipeline, steel frame, bridge & plant facilities for effective, long-term substrate protection.

Anti-Corrosion Polyurethane

Polyurethane coatings are often used for the corrosion protection of steel because they are particularly economical to apply. They dry quickly & can therefore be over-coated in short intervals. They can also be applied independently of the weather conditions & are resistant to impact.

CARC Water-Based

Chemical Agent Resistant Coating (CARC) is available in a water-based solution for environmental protection.

CARC Epoxy Multi-Component

Chemical Agent Resistant Coating (CARC) is a paint commonly applied to military vehicles to provide protection against chemical & biological weapons. The surface of the paint is engineered to be easily decontaminated after exposure to chemical warfare & biological warfare agents. The paint is also resistant to damage & removal by decontaminating solutions.

CARC Polyurethane Multi-Component

Chemical Agent Resistant Coating (CARC) can be two-component polyurethane paint commonly applied to military vehicles to provide protection against chemical & biological weapons.

UV Material Epoxy Multi-Component

UV-resistant epoxy systems mixed with hardener cure faster & in moist conditions.

UV Material 100% Solid

UV coatings can be formulated up to 100% solids so that they have no volatile component that contributes to pollution.

UV Material Water-Based

Water-based UV coatings can be considered aesthetically equivalent to bi-component acrylic & polyurethane solvent-based coatings. The range is composed of both pigmented & transparent products.

UV Material Epoxy

UV curable epoxy systems do not require the addition of curing agents. They cure within minutes, or even seconds, and have unlimited working times.

UV Material Polyurethane Multi-Component

The UV polyurethane multi-components are especially designed for very strong UV stability. Mixing with hardener gives very high durability & UV resistance.

UV Material Polyurethane

The UV polyurethanes are especially designed for UV stability, The coating is long lasting, offers excellent substrate protection, provides an attractive finish & is user-friendly.

Top Coat Polyurethane Multi-Component

Polyurethane Top Coat is a two- or three-pack isocyanate-cured polyurethane that gives a durable, high gloss finish. Isocyanates included in the hardener are moisture-sensitive & need a specific process for insulating the circuit.

Top Coat Epoxy

Top Coat Epoxys are used for decorative flooring applications, such as Terrazzo flooring, chip flooring & colored aggregate flooring.

Top Coat Epoxy Multi-Component

Two-part epoxy coatings were developed for heavy duty service on metal substrates & use less energy than heat-cured.

Top Coat Water-Based

Water-based polyurethane is popular because of its low odor & low toxicity. It goes on clear without adding a faint color like oil-based versions do & it dries much faster.