Fpro WBE Airspray Manual Conventional Spray Gun
- NEW - Compatible BSP and NPS fittings
- Standard in Airspray for water-based enamels (porcelain)
- Effortlessly Perfect Spraying
The new design of the Fpro P WBE has been made to spray very abrasive products (porcelain & ceramics), keeping the high spray performances of the original Fpro versions while reducing maintenance costs: the heat-treated nozzle lasts longer, the special needle design, featuring a polyurethane (PU) needle tip creates a soft contact on the nozzle reducing wear. This 2 part needle concept allows the replacement of needle tip only and not the complete needle assembly.
The PATENTED pending innovative restrictor controls and pre-atomizes the paint into smaller droplets. It also slows down the paint speed and leaves time for the aircap to atomize the paint at the perfect droplet size: reducing the paint bouncing off the part and increasing transfer efficiency.
The Fpro WBE can be fed by our range of diaphragm pumps, low pressure piston pumps, or our new range of Airspray tanks.
Designation | Value | Unit: metric (US) |
---|---|---|
Maximum Fluid Pressure | 6 (87) | bar (psi) |
Maximum Fluid Outlet | 450 (15.2) | cc/min (oz/min) |
Minimum Fluid Outlet | 200 (7) | cc/min (oz/min) |
Maximum Air Pressure | 6 (87) | bar (psi) |
Recommended Air Pressure (min) | 3 (43.5) | bar (psi) |
Air Consumption | 17.5 - 36.1 (10.3 - 21.2) | m3/h (cfm) |
Transfer Efficiency | 63 | % |
Maximum Fluid Temperature | 50 (122) | °C (°F) |
Air Inlet | M 1/4 NPS/BSP compatible | |
Fluid Inlet | M 3/8 NPS/BSP compatible | |
Wetted Shares: Treated Stainless Steel, Stainless Steel, PU | ♦ | |
Weight | 480 (16.9) | g (oz) |
Designation | Nozzle size | Air Consumption | Max Fluid Viscosity (CA4) | Fluid Output | Fan width at 20cm (8in) | Part number |
---|---|---|---|---|---|---|
Gun FPro P CONV Solo | - | - | - | - | - | 135774000 |
Gun FPro P CONV-09-Lwb | 0.9 mm (0.035 in) | 30 m3/h (17.6 cfm) | < 20 s | 250 cc/mn (8.5 oz/mn) | 31 cm (12.2 in) | 135779909 |
Gun FPro P CONV-12-Lwb | 1.2 mm (0.047 in) | 32.5 m3/h (19.1 cfm) | 20 - 40 s | 300 cc/mn (10.1 oz/mn) | 35 cm (13.8 in) | 135779912 |
Gun FPro P CONV-15-Lwb | 1.5 mm (0.059 in) | 34 m3/h (20 cfm) | 20 - 40 s | 350 cc/mn (11.8 oz/mn) | 36 cm (14.2 in) | 135779915 |
Gun FPro P CONV-18-Lwb | 1.8 mm (0.071 in) | 36.1 m3/h (21.2 cfm) | 20 - 40 s | 400 cc/mn (13.5 oz/mn) | 39 cm (15.4 in) | 135779918 |
Gun FPro P CONV-23-Lwb | 2.3 mm (0.091 in) | 17.5 m3/h (10.3 cfm) | > 40 s | 450 cc/mn (15.2 oz/mn) | 36 cm (14.2 in) | 135779923 |
Designation | Nozzle size | Air Consumption | Max Fluid Viscosity | Fluid Output | Fan width at 20cm (8in) | Part number |
---|---|---|---|---|---|---|
Projector FPro P CONV-07-Lwb | 0.7 mm (0.028 in) | 28 m3/h (16.5 cfm) | < 20 s | 200 cc/mn (6.8 oz/mn) | 27.5 cm (10.6 in) | 131774907 |
Projector FPro P CONV-09-Lwb | 0.9 mm (0.035 in) | 30 m3/h (17.6 cfm) | < 20 s | 250 cc/mn (8.5 oz/mn) | 31 cm (12.2 in) | 131774909 |
Projector FPro P CONV-12-Lwb | 1.2 mm (0.047 in) | 32.5 m3/h (19.1 cfm) | < 20 s | 300 cc/mn (10.1 oz/mn) | 35 cm (13.8 in) | 131774912 |
Projector FPro P CONV-15-Lwb | 1.5 mm (0.059 in) | 34 m3/h (20 cfm) | 20 - 40 s | 350 cc/mn (11.8 oz/mn) | 36 cm (14.2 in) | 131774915 |
Projector FPro P CONV-18-Lwb | 1.8 mm (0.071 in) | 36.1 m3/h (21.2 cfm) | 20 - 40 s | 400 cc/mn (13.5 oz/mn) | 39 cm (15.4 in) | 131774918 |
Projector FPro P CONV-23-Lwb | 2.3 mm (0.091 in) | 17.5 m3/h (10.3 cfm) | > 40 s | 450 cc/mn (15.2 oz/mn) | 36 cm (14.2 in) | 131774923 |
Designation | Gun included | Paint Feed | Air Hose | Fluid Hose | Regulators | Part number |
---|---|---|---|---|---|---|
Pack Abrasive "FPro P CONV + PMP150 E" | FPro P Conv-15-Lwb | PMP150 E Wall mounted | Length 7.5m - ID8mm | Length 7.5m - ID6.5mm | 1 | 151280125 |
Format : application/pdf
Size : 431Ko
Format : application/pdf
Size : 14Mo
Format : application/pdf
Size : 3Mo
Format : application/pdf
Size : 972Ko
Format : application/pdf
Size : 2Mo