Electrostatic AIRMIX® solution with ISOCUBE for water-based paints

The Nanogun Airmix® spraygun must be fitted with our genuine Airmix® spray tips to guarantee the best finish quality, minimum overspray, and pattern repeatability.

You must choose the right tip required for thickness and fan width pattern (for example, use 09.09 tip size to apply 90 µm in manual applications). To help you select your spray tip, please refer to the tip configurator. 

Tips and Tricks:  At the end of the day, leave the aircap and nozzle  - only those 2 parts - in the water until the next use.

The Nanogun Airmix® H20 version does not require ATEX compliance and can be use in job coaters activities as long as the ventilation is correctly renewed. 

Tips and Tricks: The use of our gun cover will  pertfectly protect your gun. When you flush, we recommend you place your gun on the side wall of the paint container to prevent any splashing.

We advise you to use low additional air to create a penetrating spray pattern which will perfectly reach recessed areas.For flat and wide surfaces, higher additional air will give a finer atomization and a wider spray pattern resulting in glossy finished surface.

Specially dedicated to the Nanogun Airmix® electrostatic spray gun : user-friendly, it yields a high voltage/current constant curve. The control panel allows to control the atomization air, the pump pressure (air for product pressure) and flow rate adjustment.

Tips and Tricks: for a safe and quick start-up, always check that the Isocube is properly grounded as the state of the art.  Then check your paint viscosity (up to 50s CA4) , then, stirr well the paint before priming. You need to start the pump smoothly to prevent air entraped in the fluid circuit.   

You will need to select the right length of hoses between the paint pump and the spray gun depending on your installation and your spray booth location . 

Tips and Tricks: For operator safety , only use our genuine hoses (7,5 and 15 m) and in any case and never make any hose extension.

This cup lub pump range represents an economical production/price ratio. Those pumps are dedicated for solvent and water-based paints.

Our Sames pump range features fluid sections made of stainless steel.  This pump is not recommended for moisture-sensitive materials. In case of multiple color changes, we recommend using the smallest hydraulic section which matches your needs to save paint and solvents materials. 

Tips and Tricks: In the case of very viscous materials, this pump type can be fed under pressure.

This free lub pump range represents the most robust paint pump in the world. Our Sames Flowmax® bellows pump range is dedicated for abrasive and moisture sensitive solvent or water-based materials. 

The fluid section is made of stainless steel. This pump is not recommended for multiple color changes.

Tips and Tricks:

• In case of viscous materials, you should never exceed 0,5 bar feeding pressure.
• Never use  a check valve integrated on the suction rod (you may damage the Flowmax® bellow) .

The main filtration can be done at the paint pump using a dedicated filter mounted at the product output of the paint pump. The filter screen need to be adjusted depending on your paint to prevent tip blockage when spraying.

We supply two different types of filters:

    the inline filter which requires a very small amount of solvent for flushing sequences
    the filter accumulator which is the one which is usually mounted on our pumps.

Tips and Tricks: Place the filter with the vessel oriented on the top to be used as an accumulator 

 Allows you to pump the material directly from a drum container. Different suction hose diameters are available regarding the viscosity of the paint. We supply suction rods for drums with a capacity of 60 liters and 200 liters.

Tips and Tricks: Even if the suction rod is not a wear part, we recommend you check it daily as the strainer is not plugged. Always keep a couple extra strainers in stock! 

An agitator will maintain all the components of the paint in constant movement preventing any deposition of pigments and will keep the best performance of the pump and the gun. It will also ensure perfect homogenous colors during the application.

Tips and Tricks: When manipulating the agitator, we highly recommend you shut down the air in the circuit , even if the ball valve is off.