40C50
Paint pump
The 40C50 pump is a medium-range, all purpose pump for high viscosity products. Up to 240 bar of fluid pressure allows Airmix® or Airless applications.
Suction rod or gravity hoppers
Two gun management available
Good chemical compatibility with GT, Chevron, PE seals
Description
Technical Data
Equipment
Accessories
Kits
Documents & Media
Technologies
Markets
Performance
♦ Economical with low air consumption
♦ Quiet air motor to preserve work environment
♦ air motor sizes available to deliver the product at the right pressure for high quality finish
Productivity
♦ Construction without dead zones for quick flushing & product changeovers
♦ Mobile seal located on the piston ensures mechanical cleaning of the fluid section internal wall during pump run
♦ Lower mobile single lip packing (GT) for improved efficiency & reduced friction
Sustainability
♦ Simple design with fewer parts for extended lifetime
♦ Polyfluid & PTFE graphite seal for improved wear resistance
♦ Triple chrome layer piston for exceptional durability
| Designation | Value |
|---|---|
| Maximum Air Pressure (bar) | 6 |
| Maximum Air Pressure (psi) | 87 |
| Fluid Output at 20 cycles / mn (gal/min) | 0.26 |
| Fluid Output at 20 cycles / mn (l/min) | 1 |
| Fluid Output at 60 cycles / mn (gal/min) | 0.8 |
| Fluid Output at 60 cycles / mn (l/min) | 3 |
| Free Flow Rate (gal/min) | 0.8 |
| Free Flow Rate (l/min) | 3 |
| Number of cycles per liter of products | 20 |
| Pump displacement (cc/cycle) | 50 |
| Pump displacement (in^3/cycle) | 3 |
| Depth (in) | 11 |
| Depth (mm) | 280 |
| Height (in) | 31.5 |
| Height (mm) | 800 |
| Width/depth (in) | 15.7 |
| Width/depth (mm) | 400 |
| Maximum Material Pressure (bar) | 240 |
| Maximum Material Pressure (psi) | 3480 |
| Pressure ratio | 40/1 |
| Air Consumption (cfm) | 12.7 |
| Air Consumption (m3/h) | 21.6 |
| Weight (kg) | 22 |
| Weight (lbs) | 48.5 |
| Maximum Temperature (°C) | 60 |
| Maximum Temperature (°F) | 140 |
| Power Source | Pneumatic |
| Air Inlet Fitting | F 3/8" BSP |
| Material Inlet Port | M 26 x x125 |
| Material Outlet Port | M 1/2" JIC |
| Wetted Parts | Hard chrome stainless steel, Polyethylene, Stainless steel 303, Tungsten carbide |
| Certification | CE II 2G T2 |
| Motor Type | Mechanical reversing block |
| Pump Type | Cup pump with balls |
| Pumping technology | Cup piston pumps |
| Sound Level (dbA) | 77 |
| Designation | Part number | Material inlet | Seal | Lower seal | Setup | Suction accessory | Air Regulator fluid pressure | Drain Rod | Pump output Filter |
|---|---|---|---|---|---|---|---|---|---|
| 40C50 Airless Bare pump | 151775000 | F1/2 BSPP | Chevron mix Polyfluid/PTFEG | GT | Bare | - | |||
| 40C50 PUMP W/M W/O FILTER W/O SUCTION ROD | 151775050 | M26x125 | Chevron mix Polyfluid/PTFEG | GT | Wall mounted | - | Yes | ||
| 40C50 PUMP W/M W/O FILTER WITH SUCTION ROD DIA 23 | 151775100 | M26x125 | Chevron mix Polyfluid/PTFEG | GT | Wall mounted | Suction rod ID 23 mm | Yes | ||
| 40C50 PUMP W/M WITH FILTER W/O SUCTION ROD | 151775150 | M26x125 | Chevron mix Polyfluid/PTFEG | GT | Wall mounted | - | Yes | Yes | Yes |
| 40C50 PUMP W/M WITH FILTER AND SUCTION ROD DIAM 23 | 151775200 | M26x125 | Chevron mix Polyfluid/PTFEG | GT | Wall mounted | Suction rod ID 23 mm | Yes | Yes | Yes |
| 40C50 PUMP TROLLEY WITH FILTER AND SUCTION ROD DIAM 25 | 151775400 | M26x125 | Chevron mix Polyfluid/PTFEG | GT | Trolley | Suction rod ID 23 mm | Yes | Yes | Yes |
| Designation | Part number |
|---|---|
| Two Post Cart w/o plate | 051221000 |
| Pump Mounting Plate with straps | 056100199 |
| SST Suction rod Ø23 plunging tube length elbowed 570 mm M26x125 | 149596150 |
| SST Suction rod Ø23 plunging tube length 1000mm elbowed (for 200 liters drums) M26x125 | 149596160 |
| Stainless steel drain rod Ø16 elbowed F18 x 125 | 049596000 |
| Fluid filter 3/8 Mesh 12 | 155580400 |
| Gravity hopper 6 liters | 151140230 |
| Designation | Part number | Aircap | Details | Spray gun | Tip | Hoses length (mm) | Air Regulator | Pump type | Suction accessory | Swivel fitting | Hoses | Regulators | Whip hose (m) |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| KIT 40C50 WALL-MOUNTED & Xcite®+ 240B & HOSE 7.5M | 151260968 | VX124 | Filter | Xcite®+ 240 | - | 7.5 | Yes | Wall mounted | Suction rod ID 23 mm | Yes | Yes | 2 | |
| PACK AIRLESS 40C50 W/M+D22 ROD+PRIMING+SFLOW 515 TIP+HOSES | 151265102 | For reversible tip | Prime kit | Sflow™ 275 4F | 12-13 | 7.5 | Yes | Wall mounted | Suction rod ID 23 mm | Yes | Yes | 1 | 1.6 |
| PACK AIRLESS 40C50 MOB SUCT ROD PRIM D25 SFLOW 275 12-13 TIP | 151265103 | For reversible tip | Prime kit | Sflow™ 275 4F | 12-13 | 7.5 | Yes | Trolley | Suction rod ID 23 mm | Yes | Yes | 1 | 1.6 |
| PACK 40C50 PUMP + SFlow®275 GUN | 151265105 | For reversible tip | Filter | Sflow™ 275 4F | 12-13 | 7.5 | Yes | Trolley | Suction rod ID 23 mm | Yes | Yes | 1 | 1.6 |
-
Catalog - Airmix® Spraying and Equipment
-
product-40c50-airmix-paint-pump-1_en_GB.pdf
-
product-40c50-airmix-paint-pump-1_en_US.pdf
-
40C50 | User manual
-
3D file 40C50
-
3D file 40C50
Airmix® technology
Let's get in touch-
What is Airmix®?
Airmix® is a technology, invented in 1975 by Kremlin, combines the advantages of airless spraying and air-assisted spraying to deliver high-quality paint application with improved transfer efficiency and reduced product consumption.
-
What are the benefits of using Airmix®?
Airmix® technology enables the application of thicker paint layers to better protect surfaces, without compromising on finish quality. Its benefits include superior finish quality, high transfer efficiency, lower paint consumption, and fast, uniform application.
-
For which types of projects is Airmix® recommended?
Airmix® technology is ideal for industrial applications where a balance between protective thickness and finish quality is required, such as furniture manufacturing, the transportation industry, and rolling equipment, among others.