A clean atomizer is a must have for a good performance of painting process. No drop on painted part is the basic you can ask to your Bell Atomizer Cleaner. So after a good cleaning, you need a good drying process to avoid any solvent drops leaving the air shroud.
The maintenance of the Bell Atomizer Cleaner is reduced to very few components : the impeller seal and bearing every year for only few minutes.
For each gun or bell cup and air shroud dimension, a specific adaptation of the cleaning box is required.
|Designation||Value||Unit: metric (US)|
|Length||6,8 (100)||mm (in)|
|Height||6 (87)||mm (in)|
|Width||12 (26.5)||mm (in)|
|Torque at 100 rpm||370 (14.6)||Nm|
|Maximum Air Consumption||220 (8.7)||m3/h (cfm)|
|Stainless Steel Construction||♦|
|ATEX Certification||II 2 G Ex h IIA T4 Gb|
|Bell Atomizer Cleaner NANOBELL 801 EC35||130002061|
|Bell Atomizer Cleaner NANOBELL 801 EC50||130002062|
|Bell Atomizer Cleaner NANOBELL 801 EX65||130002063|
|Bell Atomizer Cleaner Nanobell 2 EC35||130002058|
|Bell Atomizer Cleaner Nanobell 2 EC50||130002059|
|Bell Atomizer Cleaner Nanobell 2 EC65||130002060|
|Bell Atomizer Cleaner Range 7 EC35 Internal Charge||130001870|
|Bell Atomizer Cleaner Range 7 EC43 & EC50 External Charge Fingerless||130002033|
|Bell Atomizer Cleaner Range 7 EC43 Internal Charge||130002057|
|Bell Atomizer Cleaner Range 7 EC50 External Charge||130001874|
|Bell Atomizer Cleaner Range 7 EC50 Internal Charge||130001871|
|Bell Atomizer Cleaner Range 7 EX65 External Charge||130001875|
|Bell Atomizer Cleaner Range 7 EX65 External Charge Fingerless||130002079|
|Bell Atomizer Cleaner Range 7 EX65 Internal Charge||130001872|
|Bell Atomizer Cleaner Range 7 EX80 External Charge||130001876|
|Bell Atomizer Cleaner Range 7 EX80 Internal Charge||130001873|
|Electrodes Cleaner PPH 707 EXT||130002039|
|Gun Atomizer Cleaner Dual gun TRP||130001991|
|Gun Atomizer Cleaner Single gun TRP||130001990|
|Gun Atomizer Cleaner Single gun AVX||130002116|
|Gun Atomizer Cleaner Single gun ASB||130002156|
|Bell Atomizer Cleaner Range 7 EX50 External Charge Fingerless||130002078|
|Gun Atomizer Cleaner Single gun A35||130002206|
|Floater Wrench EC35/EC50/EX65 Internal Charge||130001901|
|Drain pipe Upper part||130001906|
|Drain pipe Lower part||130001907|
|Purge Adapter for cleaning the box (2K)||130001930|
|Impeller elevator part for 2K version||130001889|
|Dump tube for purging gun||130002212|
|Impeller Kit (includes bearings, seal & stem) for EC35/EC50/EX65 Internal Charge & EX65/EX80 External Charge||130001896|
|Impeller Kit (includes bearings, seal & stem) for EC50 External Charge||130001897|
|Impeller Kit (includes bearings, seal & stem) for EX80 Internal Charge||130001898|
|Air cap for TRP500||130002130|
|Air cap for AVX||130002129|
|Air cap for ASB||130002151|
Epoxy primer/sealer is a non-porous finish that is typically recommended as the first base coat over bare steel.
Epoxy primer/sealer multi-component is a non-porous finish base mixed with a hardener that is typically recommended as the first base coat over bare steel.
Designed to hide profile & surface imperfections, multi-component polyurethane primers & sealers improve adhesion of top coats to the substrate due to the addition of a hardener.
Designed to hide profile & surface imperfections, water-based primers & sealers are environmentally friendly.
Designed to hide profile & surface imperfections, polyurethane primers & sealers promote adhesion of top coats to the substrate.
Polyurethane Top Coat is a two- or three-pack isocyanate-cured polyurethane that gives a durable, high gloss finish. Isocyanates included in the hardener are moisture-sensitive & need a specific process for insulating the circuit.
Top Coat Epoxys are used for decorative flooring applications, such as Terrazzo flooring, chip flooring & colored aggregate flooring.
Two-part epoxy coatings were developed for heavy duty service on metal substrates & use less energy than heat-cured.
Water-based polyurethane is popular because of its low odor & low toxicity. It goes on clear without adding a faint color like oil-based versions do & it dries much faster.
The newest metallic epoxy system on the market allows contractors to heighten the effects & make floors look three-dimensional.
Polyurethane water-based coatings offer a very high chemical/physical resistance & steel effect & are environmentally friendly.
A two-component 100%-solid epoxy blended with metallic pigments, Metal Fusion is self-leveling, allowing easy application & seamless floor surfaces.
Polyurethane coatings are particularly recommended for application to surfaces subject to high levels of wear & tear where excellent chemical/physical resistance is required. The metallic parts will give a steel effect.
Protection, bonding, finishing & sealing for composite & plastic parts